Amiga Hardware DatabaseSearch Result
9 expansions found
Manufacturer DKB, USA | Date 1990 | Amiga A2000, A3000, A4000 | Interface Zorro II | Autoconfig ID 2012 / 1 |
- reset resistant RAM disk - keeps its contents over months
- 16 DIL sockets for up to 8 MB static RAM
- supports 32k×8, 128k×8 and 512k×8 SRAM chips in groups of two
- memory types cannot be mixed
- autoboot ROM - autobooting requires Kickstart 1.3
- autoboot disable switch
- hardware and software write protection
Advert (US)
1990-12
Advert (US)
1991-04
Manufacturer DKB, USA | Date 1993 | Amiga A1200 | Interface trapdoor slot | Autoconfig ID 2012 / 16 |
- optional PLCC FPU, up to 68882 @ 40 MHz
- two 72 pin SIMM sockets accept 8 MB RAM
- supports 1, 2 or 4 MB SIMMs
- does not conflict with the PCMCIA port even with 8 MB RAM added
- battery backed up clock
front side
front side
back side
back side
- DKB-ThePeripheralGuide.pdf
DKB Brochure "The Peripheral Guide"
318 kB
Advert (US)
1993-10
Manufacturer DKB, USA | Date 1992 | Amiga A2000 | Interface special (see text), |
- plugs into the CPU direct slot of the Commodore A2630
- four 72 pin SIMM sockets accept 112 MB RAM
- supports 4, 8, 16, 32 MB SIMMs, 80 ns or faster
- DKB Mix 'n Match Technology allows different size SIMM in the same bank
- burst RAM access
- does not work with A2630 Rev. 6
Rev E, front side
Rev E, front side
Rev E, back side
- DKB-ThePeripheralGuide.pdf
DKB Brochure "The Peripheral Guide"
318 kB - DKB_2632.pdf
user manual
987 kB
- DKB2632.dms
install disk
65 kB
Advert (US)
1992-04
Advert (US)
1992-12
Manufacturer DKB, USA | Date 1993 | Amiga A3000, A4000 | Interface Zorro III | Autoconfig ID 2012 / 14 |
- four 72 pin SIMM sockets accept 128 MB RAM
- supports 4, 8, 16, 32 MB SIMMs 80 ns or faster
- when different size of SIMMs are installed the "3128" program has to be added to the beginning of the Startup-Sequence - otherwise the system will assume that every SIMM is as large as the largest one
- if used with a Commodore A3640 processor board, that must be at least revision 3.1
front side
back side
- DKB-ThePeripheralGuide.pdf
DKB Brochure "The Peripheral Guide"
318 kB - DKB3128.pdf
installation and user manual
100 kB
- DKB3128-10.dms
install disk
3128 program v1.0 (1993-07-10)
75 kB
Advert (US)
1993-11
Manufacturer DKB, USA | Date 1987 | Amiga A1000 | Interface 68000 socket |
- 32 DIP sockets for 1 MB RAM
- 256k×1 DIPs
- autoconfigures under Kickstart 1.2, requires AddMem under Kickstart 1.1
- the starting memory address is DIP switch selectable to one of nine address blocks
- the memory can be disabled / enabled by software
- battery backed up clock
- connects to the 68000 socket
- two or four (depending on revision) jumper wires have to be connected to the motherboard
- can be installed together with the DKB KwikStart - Insider has to be on the top of the KwikStart
front side
Advert (US)
1987-03
Manufacturer DKB, USA | Date 1989 | Amiga A1000 | Interface 68000 socket |
- Internal FastRAM Expansion
- twelve DIP sockets accept 1.5 MB RAM
- supports 256k×4 DIPs only
- accepts DIPs in groups of four giving 0.5, 1, 1.5 MB configurations
- battery backed up clock
- connects to the 68000 socket, the 68000 is replaced onto the board
- compatible with the DKB KwikStart II and ICD AdSpeed boards
- NTSC A1000s: a clip has to attached to pin 14 of the chip at location P6 on the daughterboard
- PAL A1000s: due to space constraints the clip doesn't fit, so it has to be cut off and the wire has to be soldered to pin 7 of the chip at location U4S on the motherboard
- RAM banks have to be occupied starting from bank 1 (the bank toward the 68000)
- DIP Switch Settings
| Switch | Setting | Description |
| 1 | OFF | Reserved |
| 2 | ON | Autoconfig ($C00000) |
| OFF | No Autoconfig ($800000) | |
| 3 & 4 | OFF & OFF | no memory installed |
| ON & OFF | bank 1 occupied (512K) | |
| OFF & ON | bank and 2 occupied (1 MB) | |
| ON & ON | all banks occupied (1.5 MB) |
front side
back side
- InsiderII.dms
Tool disk
19 kB
Advert (US)
1990-12
Advert (US)
1991-04
Advert (US)
1991-07
Advert (US)
1992-01
Advert (US)
1992-12
Manufacturer DKB, USA | Date 1991 | Amiga A2000 | Interface Agnus socket |
- 1 MB Chip RAM expansion
- connects to the Agnus' socket
- a fly is connected to pin 36 of Gary
- Agnus is replaced with Super Agnus which allows a total of 2 MB chip RAM
- rules out internal processor cards and internal memory expansions with more than 512 kB RAM
front side
Advert (US)
1990-12
Advert (US)
1991-04
Advert (US)
1991-07
Manufacturer DKB, USA | Date 1992 | Amiga A500, A2000 | Interface Agnus socket |
- 1 MB Chip RAM expansion
- connects to the Agnus' socket
- a fly is connected to pin 36 of Gary
- Agnus is replaced with Super Agnus which allows a total of 2 MB chip RAM
- rules out internal processor cards and internal memory expansions with more than 512 kB RAM
front side
back side
- DKB-ThePeripheralGuide.pdf
DKB Brochure "The Peripheral Guide"
318 kB - MegAChip.pdf
Installation and User's Guide (english)
758 kB
Advert (US)
1992-01
Advert (US)
1992-04
Advert (AU)
1992-10
Advert (US)
1992-12
Advert (US)
1992-12
Manufacturer Michigan Software, USA | Date 1986 | Amiga A1000 | Interface trapdoor slot |
- 256 kB Chip RAM expansion
- connects to the front panel expansion slot
Advert (US)
1986-04