Search Result
11 expansions found
A1291 (Stingray) A530 G-Force 030 (Impact A2000-030 Combo Series II) G-Force 040 Impact A2000-030 Combo Impact A2000-HC Series II Impact A2000-HC+8 Series II Impact A4000-HC+8 (A4008) Impact A500 HD8+ Series II IOExtender PhonePak VFX
SCSI controller
A1291 is the optional SCSI controller for the A1230 Turbo+ II
SCSI 2 DMA controller (WD3393 or AM33C93A)
DB25 external connector
active termination
FaaastROM driver (gvpscsi.device)
supported by NetBSD
A1291, front side
A1291, back side
Advert (AU) 1994-07
processor
68EC030 @ 40 MHz PGA
optional 68882 @ 40 MHz PGA
memory
two 64 pin SIMM sockets accept 1, 2, 4 or 8 MB RAM
supports special 1 or 4 MB GVP SIMMs
SIMM sizes cannot be mixed
hardware maprom
SCSI 2 DMA controller
FaaaST ROM SCSI driver
3.58 MB/s maximum transfer speed
50 pin internal SCSI connector
DB25F external SCSI connector
hard disk activity LED
place for a 3.5" hard disk inside the case
supported by Linux and NetBSD
notes
mini expansion slot for the optional GVP PC286 AT emulator
connects to the side expansion port
no passthrough connector
disable switch on top of the case
in 68000 fallback mode both the RAM and hard disk are deactivated
external power supply
built in fan
jumper settings
J1 - MMU: ON - disable
J2 - 68000 fallback mode: OFF - enable
J3 - CPU cache: ON - disable
J9 - autoboot: OFF - disable
J11 - RAM: ON - not installed, OFF - installed
J13 - SIMM size: ON - 4 MB, OFF - 1 MB
J4, J6 ON J5, J7, J8, J10, J12 OFF CN7, CN18 1-2 CN8, CN11 2-3 - reserved
Case opened, top side
Exterior, front side
PCB, front side
PCB, back side
Exterior, front side
Case opened (with PC286 installed), front side
Exterior, back side
Case opened (with PC286 installed), back side
Advert (DE) 1992-11 Advert (DE) 1993-02 Advert (US) 1992-09 Advert (FR) 1992-10 Advert (US) 1992-11 Advert (US) 1993-03 Advert (FR) 1993-05 Advert (US) 1993-06
processor
68EC030 @ 25 / 40 MHz or 68030 @ 50 MHz, PGA
68882 @ 25 / 40 / 50 MHz, PGA - clocked at the same speed as the 68030
memory
25 MHz: 1 MB on board + three SIMM sockets gives 13 MB max
40 / 50 MHz: 4 MB on board + three SIMM sockets gives 16 MB max
supports only special 64 pin 1 or 4 MB 60 ns GVP SIMMs
maximum 8 MB is autoconfigured in the 16 MB address space, the exact amount is set by jumper
the remaining memory is configured as extended memory by the FaaastROM driver
Impact Series II SCSI controller
1.2 MB/s transfer speed
direct DMA transfer to onboard Fast RAM
FaaastROM SCSI driver (gvpscsi.device) - auto booting requires at least Kickstart 1.3
DB25 external connector
50 pin internal header
supported by Linux and NetBSD
optional hard disk mounting kit allows installing any 1" drive on the back of the card
notes
32 bit expansion bus for the EGS 110/24 graphics board
if the EGS 110/24 is installed no place remains for the hard disk mounting kit
68000 fallback mode switchable either by software or jumper
in 68000 fallback mode RAM and SCSI is also switched off
Kickstart remapping
jumper settings
rev 3
J5 ON OFF ON J6 OFF ON ON J11 OFF ON OFF CN8 2-3 OFF 1-2 - board type - 25 MHz - 40 MHz - 50 MHz
J2 - 68000 fallback mode: OFF - enable
J3 - MMU: ON - disable
J9 - autoboot ROM: OFF - disable
J12 - bank 1-2 memory address: ON - Zorro II address space, OFF - 0x01000000
J14 - SCSI drive: OFF - connected
CN6 - HDD LED
CN16 - FPU clock: 2-3 - uses CPU clock
J4 ON J7, J8, J10, J13, J15 OFF CN7, CN15 1-2 CN14 2-3 - reserved
rev 4 (additional jumpers to rev 3)
J16 - DTACK pull-up for old A2000s: ON - enable
CN15 - autoboot ROM version: 1-2 - v4.5; 2-3 - before v4.5
CN17 2-3 1-2-3 - 25 MHz, 50 MHz - 40 MHz
Rev 3, front side
Rev 3, front side
Rev 3, back side
Rev 4, front side
Rev 4, front side
Rev 4, back side
Advert (DE) 1991-06 Advert (DE) 1992-10 Advert (DE) 1993-02 Advert (US) 1998-05 Advert (US) 1992-02 Advert (US) 1992-03 Advert (FR) 1992-05 Advert (US) 1992-09 Advert (US) 1993-06 Advert (US) 1993-11
memory
four 64 pin SIMM sockets accept 64 MB RAM
supports only special 4 or 16 MB GVP SIMMs
SIMM sizes cannot be mixed
040 burst mode requires all four sockets to be filled up
Kickstart remapping
SCSI 2 DMA controller
not Fast SCSI 2 - the same electronic as the GVP Series II controllers
no termination power is fed to the external SCSI connector - active termination must be used
50 pin internal SCSI header
DB25 external connector
RDB compatible
supported by Linux and NetBSD
I/O
RS232 compatible 9 pin buffered serial port
614140 bps max transfer speed
Centronics parallel port
selectable IBM / Amiga compatible mode
notes
32 bit expansion bus for the EGS 110/24 graphics board
jumper settings
J4 - SCSI drive: OFF - connected
J5 - autoboot ROM: OFF - disable
J7 - MMU: ON - disable
J20 - SIMM size: ON - 4 MB, OFF - 16 MB
J22 - burst mode: OFF - enable
J26 - DTACK pull-up for old A2000s: ON - enable
CN9 - parallel port mode: 1-2 - Amiga, 2-3 - IBM
J10, J16, J21, J24, J27 ON J2, J3, J8, J15, J17, J18, J19, CN19 OFF CN12, CN20 1-2 CN11 2-3 - reserved
front side
front side
back side
Advert (DE) 1993-02 Advert (US) 1992-09 Advert (US) 1993-06 Advert (US) 1993-11 Advert (US) 1994-04
processor
68030 @ 22 / 33 MHz, QFP
68882 @ 22 / 33 MHz, PLCC surface mounted
the CPU and FPU are clocked at the same speed by the same oscillator
memory
22 MHz: 1 MB preinstalled, expandable to 13 MB RAM
33 MHz: 4 MB preinstalled, expandable to 16 MB RAM
three 64 pin SIMM sockets accept 1 or 4 MB GVP SIMMs
Impact Series II SCSI controller
WD33C93 controller IC
direct DMA transfer to onboard Fast RAM
FaaastROM SCSI driver (gvpscsi.device) - auto booting requires at least Kickstart 1.3
DB25 external connector
50 pin internal header
optional hard disk mounting kit allows installing any 1" drive on the back of the card
jumper settings
J10 ON OFF J13 OFF ON - memory address - outside Zorro II address space - Zorro II address space (with 1 MB SIMMs only)
J3 - MMU: ON - disable
J4 - SCSI drive: OFF - connected
J6 - 68000 fallback mode: OFF - enable
J9 - autoboot ROM: ON - disable
J7, J12, J15, J17, J18, J19, J22 ON J8, J11, J14, J16, J20 OFF J21, CN7, CN8 1-2 - reserved
Rev 3, front side
Rev 3, back side
Rev 4, front side
Rev 4, back side
Advert (US) 1991-05 Advert (FR) 1991-06 Advert (US) 1991-09 Advert (FR) 1991-10 Advert (AU) 1991-08 Advert (FR) 1992-02
Company
Great Valley Products , USA Date
1990Amiga
A2000, A3000, A4000Interface
Zorro IIAutoconfig ID
2017 / 10,11
SCSI 2 DMA controller
WD 33C93A @ 14 MHz
3.58 MB/s transfer speed
FaaastROM SCSI driver (gvpscsi.device) - autobooting requires at least Kickstart 1.3
autoboot disable jumper
RDB compatible
place for a 3.5" hard disk on the card
50 pin internal SCSI header
DB25 external connector
hard disk activity LED connector
no termination power
A-Max II driver (gvpscsi.amhd)
supported by Linux and NetBSD
memory
eight 30 pin SIMM sockets accept 8 MB RAM
accepts SIMMs in groups of two, giving 2, 4, 6 or 8 MB configurations
this memory is technically not Zorro II memory - data is DMA-d from the HD as normal, but not via the Zorro bus for added speed
jumper settings
J5 OFF OFF ON OFF OFF
J6 OFF ON OFF OFF ON
J7 ON OFF OFF ON OFF
J8 OFF OFF OFF ON ON
J9 ON ON ON OFF OFF
- memory - 0 MB - 2 MB, CN10-CN11 - 4 MB, CN10-CN13 - 6 MB, CN10-CN15 - 8 MB, CN10-CN17
J3 - autoboot ROM
J4 - SCSI drive
J10-J12 - SCSI ID
Rev II with RAM and Guru-ROM installed, front side
Rev II with RAM, front side
Rev 4, front side
Rev 4, back side
Rev II with RAM and Guru-ROM installed, back side
Advert (DE) 1990-10 Advert (US) 1990-09 Advert (FR) 1990-10 Advert (US) 1990-11 Advert (US) 1991-04 Advert (FR) 1991-04 Advert (US) 1991-11 Advert (FR) 1991-11 Advert (US) 1992-11
Company
Great Valley Products , USA Date
1993Amiga
A2000, A3000, A4000Interface
Zorro IIAutoconfig ID
2017 / 10,11
Advert (US) 1993-11 Advert (US) 1994-04
SCSI 2 DMA controller
3.58 MB/s transfer speed
FaaasT ROM SCSI driver (gvpscsi.device) - autobooting requires at least Kickstart 1.3
RDB compatible
place for a 3.5" hard disk inside the case
50 pin internal header
DB25 external connector
supported by Linux
A-Max II driver (gvpscsi.amhd)
memory
four 30 pin SIMM sockets accept 8 MB RAM
accepts 1 or 4 MB 120 ns SIMMs
supports 2, 4 or 8 MB configurations
the 4 MB configuration requires four 1 MB modules, a 4 MB module is not sufficient
fully autoconfiguring
notes
connects to the side expansion port
has no passthrough connector
stylish design matches the A500
disable switch
hard disk activity LED
external power supply
built in fan
mini expansion slot for the optional PC emulator card
problems may arise with the combination of A500, 8372A Agnus and an internal memory expansion with CPU or Gary adaptor - a trace has to be cut to solve the problem
jumper settings
J5 OFF OFF ON ON
J6 OFF ON OFF OFF
J7 ON OFF OFF OFF
J8 ON ON ON OFF
J9 OFF OFF OFF ON
J12 1-2 1-2 1-2 2-3
- memory - 0 MB - 2 MB, CN9-CN10 - 4 MB, CN9-CN12 - 8 MB, CN9-CN10
Case opened, top side
Exterior, top side
Exterior, rear side
Exterior, right side
PCB Rev 3, front side
PCB Rev 6, front side
PCB Rev 3, back side
Advert (DE) 1991-01 Advert (DE) 1992-10 Advert (DE) 1992-11 Advert (US) 1990-11 Advert (FR) 1990-11 Advert (FR) 1991-05 Advert (US) 1991-09 Advert (FR) 1991-11 Advert (US) 1991-12 Advert (US) 1992-02 Advert (FR) 1992-03 Advert (US) 1992-09 Advert (US) 1992-11 Advert (US) 1993-03 Advert (FR) 1993-05 Advert (US) 1993-06